Beginner's Plumbing: What You Need for Installing a Bathtub
Beginner's Plumbing: What You Need for Installing a Bathtub
Blog Article
We have unearthed the article about A Step-by-Step Guide to Installing a Bathtub below on the net and think it made sense to discuss it with you on this page.
Mounting a bathtub isn't specifically brain surgery, however it does need strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately tough job. If the old bathtub is easily obtainable, the task can relocate quickly; if you have to open up a wall to eliminate the old bathtub and place the new bathtub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require an assistant to move out the old tub and embeded in the new one. See to it you have qualified yourself for the work as well as fit attempting it. As opposed to employing a professional to take control of a halfway-completed project, it is far better to think about using one before you begin. Opportunities are you may need an expert plumber to make tube links.
This write-up will assist you mount a new tub in your shower room if you have actually currently acquired a brand-new bathtub and also do not require to change the arrangement of your previous water system pipelines.
Your devices as well as product list should consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome due to the limited accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel ready for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the maker provided backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former kind needs to be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed position. The wood boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by examining the spirit level as well as adjusting the feet on the bathtub up until the spirit level reviews level.
To mount faucets, fit all-time low of the furthest adaptable tap connector to the proper supply pipeline by making a compression join; after that do the very same for the various other faucet.
Activate the water supply and check all joints and brand-new pipework for leaks and also tighten them if essential. Fill up the bathtub and likewise inspect the overflow outlet and also the typical outlet for leaks.
Finally, fix the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub needs to wait up until the bathtub has actually been used at the very least once as this will certainly settle it into its last position.
Planning for the Setup
To start with, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its last placement.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a stiff seal, causing the water to penetrate the wall surface between the bath and the tiling, leading to issues with wetness and feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components and installations. They are marketed in tubes and also cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealer can crack relatively early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our article on How to Install a Bathtub Yourself. Thanks for finding the time to browse our article. If you enjoyed our blog entry kindly remember to pass it around. Thanks a lot for taking the time to read it.
This Website Report this page